Author Topic: Small Fry / Laminate Plate help  (Read 1094 times)

Online anyfish

  • Kicker
  • ****
  • Posts: 237
Small Fry / Laminate Plate help
« on: 02/06/21 18:42 UTC »
I recently picked up a laminate plate for my small fry mold.  After I remove the plate and inject the second color, it fills in the empty space but also covers the first color just a little.  What am I doing wrong?  I appreciate any help.

Offline ctom

  • Lunker
  • *****
  • Posts: 11047
Re: Small Fry / Laminate Plate help
« Reply #1 on: 02/06/21 18:55 UTC »
Make sure the bottom side is firmly back in place, then use slightly cooler plastic and slowdown the injection speed/pressure on the plunger.
There are good ships
and wood ships
ships that sail the sea
but the best ships are friendships
and may they
always be ......An Irish Toast

Online anyfish

  • Kicker
  • ****
  • Posts: 237
Re: Small Fry / Laminate Plate help
« Reply #2 on: 02/06/21 19:28 UTC »
Thanks for the help.  I'll give it a try.

Online anyfish

  • Kicker
  • ****
  • Posts: 237
Re: Small Fry / Laminate Plate help
« Reply #3 on: 02/07/21 15:30 UTC »
Thanks again Tom.  Injection temp was the key.  Everything works good now.

Offline Bass Boys

  • Kicker
  • ****
  • Posts: 146
Re: Small Fry / Laminate Plate help
« Reply #4 on: 02/07/21 15:41 UTC »
 What temp do you think the second color was at when it worked good  ??
 apx. 350 ??
 

Offline ctom

  • Lunker
  • *****
  • Posts: 11047
Re: Small Fry / Laminate Plate help
« Reply #5 on: 02/07/21 16:35 UTC »
On the smaller fry molds and a second injection, 350 is too hot at normal injection speeds/pressure. 320-330 is better and inject slower, holding pressure when the injector rod stops.
There are good ships
and wood ships
ships that sail the sea
but the best ships are friendships
and may they
always be ......An Irish Toast

Online anyfish

  • Kicker
  • ****
  • Posts: 237
Re: Small Fry / Laminate Plate help
« Reply #6 on: 02/07/21 17:13 UTC »
Just what Tom said.  I was at about 350 and had the problem.   Tried at about 320 and slowed down and no problems. 

Offline ctom

  • Lunker
  • *****
  • Posts: 11047
Re: Small Fry / Laminate Plate help
« Reply #7 on: 02/07/21 19:24 UTC »
The gates are quite large on these baits so if the plastic is too warm [think thin] or if the injection rate is too fast [too much pressure] it causes the belly side to lift up when the second color goes in and you'll get that color above and below the already in place color.
There are good ships
and wood ships
ships that sail the sea
but the best ships are friendships
and may they
always be ......An Irish Toast

Offline Bass Boys

  • Kicker
  • ****
  • Posts: 146
Re: Small Fry / Laminate Plate help
« Reply #8 on: 02/08/21 05:42 UTC »
Got cha , makes sense.

Offline ctom

  • Lunker
  • *****
  • Posts: 11047
Re: Small Fry / Laminate Plate help
« Reply #9 on: 02/08/21 07:46 UTC »
Got cha , makes sense.

Bass Boys..... Sorry I missed you. Welcome to the Do-It forums !
There are good ships
and wood ships
ships that sail the sea
but the best ships are friendships
and may they
always be ......An Irish Toast

Offline efishnc

  • Lunker
  • *****
  • Posts: 2138
Re: Small Fry / Laminate Plate help
« Reply #10 on: 02/08/21 09:33 UTC »
I've always kept my temps the same to ensure a good weld, but without question, injecting S-L-O-W-E-R is key for keeping the other half of the laminate in place.

Offline Bass Boys

  • Kicker
  • ****
  • Posts: 146
Re: Small Fry / Laminate Plate help
« Reply #11 on: 02/08/21 13:43 UTC »
Bass Boys..... Sorry I missed you. Welcome to the Do-It forums !

 Thanks ,
 I only have 1 mold with a plate and its a bigger bait , Most of my laminates are done hand pour and with that it needs 350 to bond . The hand pour does not put pressure on the 1st half like an injection mold would.

Offline ctom

  • Lunker
  • *****
  • Posts: 11047
Re: Small Fry / Laminate Plate help
« Reply #12 on: 02/08/21 14:09 UTC »
BBoys....if you are hand pouring then you should keep the temp of each plastic very close to each other. Injecting its not so important but you still need to have somewhere in the neighborhood of 320+ degrees to weld well. Hold some pressure really binds the weld.
There are good ships
and wood ships
ships that sail the sea
but the best ships are friendships
and may they
always be ......An Irish Toast