Custom Baits - Forum

Soft Plastic Bait Making => Getting Started / Customer Support => Topic started by: Steve J on 02/19/17 13:16 UTC

Title: MF powder for soft plastics
Post by: Steve J on 02/19/17 13:16 UTC
Anybody use the powder rather than the liquid colorant?
How much powder to 1 drop of liquid?
Title: Re: MF powder for soft plastics
Post by: Mike J on 02/19/17 14:08 UTC
I've never used MF but I do use other kinds of powders.  If you have the pinch smidgen dash spoons I usually start with the pinch in 4 oz and some colors I end up with closer to a dash. You really just have to play with each color to get it to the way you like it.
Title: Re: MF powder for soft plastics
Post by: Steve J on 02/19/17 14:29 UTC
Do you put the powder in before or after you heat it?
Title: Re: MF powder for soft plastics
Post by: Mike J on 02/19/17 14:43 UTC
I've done both ways.  I usually put it in raw plastic if I'm starting out knowing exactly what I want to put in, but you can add it after its hot too.
Title: Re: MF powder for soft plastics
Post by: Muskygary on 02/19/17 15:54 UTC
Now I also use pro tec powder paint in my plastics. I thought that if you warmed the plastic up first the powder might clump, so I always put my powder in cold plastic. As far as the right amount, you just have to eye ball it and try, try, again!
Title: Re: MF powder for soft plastics
Post by: Apdriver on 02/19/17 17:20 UTC
I've never used MF but I do use other kinds of powders.  If you have the pinch smidgen dash spoons I usually start with the pinch in 4 oz and some colors I end up with closer to a dash. You really just have to play with each color to get it to the way you like it.

Hey Mike, is that pinch smidgen dash thing an ingredient measurement? I can see where it would be useful, but have never seen a measuring device for that.
Title: Re: MF powder for soft plastics
Post by: MT204 on 02/19/17 17:26 UTC
I had never heard of such a thing till I came to this forum either.
Yes there is such a thing.
https://www.amazon.com/Norpro-Stainless-Measuring-Spoons-smidgen/dp/B0009X1P9S/ref=pd_lpo_79_bs_lp_t_2/167-1615781-6849442?_encoding=UTF8&psc=1&refRID=NNM71VTYEE4K5DN36V46
Title: Re: MF powder for soft plastics
Post by: Lines on 02/19/17 18:18 UTC
I picked up a set of these measuring spoons at a local Amish variety store. Stainless steel too.
Title: Re: MF powder for soft plastics
Post by: Bass in the hood on 02/19/17 18:33 UTC
I also use the small measuring spoons for both glitter and powders. They may not be ready  available but I find them very useful for making consistent baits. I purchased mind from lure craft and every once in awhile I find them in a retail store.
www.bassinthehood.com
Title: Re: MF powder for soft plastics
Post by: Steve J on 02/19/17 18:49 UTC
I just purchased a set on ebay.
Less than $4 including shipping.
Title: Re: MF powder for soft plastics
Post by: BareKnuckleJigs on 02/19/17 19:59 UTC
My current set is 5 spoons, Drop, Smidgen, Pinch, Dash, Tad.  Stainless, inexpensive, indispensable.

If You may do any hand-pouring, get a Stainless Steel Drizzle Spoon.
Title: Re: MF powder for soft plastics
Post by: Mike J on 02/19/17 20:12 UTC
Yep that's what I use. I bought the lure craft ones.  They are great to keep things consistent.
Title: Re: MF powder for soft plastics
Post by: ctom on 02/19/17 21:14 UTC
I picked up a set of these measuring spoons at a local Amish variety store. Stainless steel too.

You weren't near Cantril were you?
Title: Re: MF powder for soft plastics
Post by: Lines on 02/20/17 06:31 UTC
Been to The Dutchman's in Cantril many times. I'm about 35 minutes due West on Hwy 2. The Zimmermans are good, hard working folks. They are Menonite, allowing more modern amenities than the Amish. There are several Amish stores around the Bloomfield-Drakesville communities.
Title: Re: MF powder for soft plastics
Post by: ctom on 02/20/17 07:35 UTC
Been to Dutchmans and Zimmermans a few times myself.
Title: Re: MF powder for soft plastics
Post by: Lines on 02/20/17 20:54 UTC
Very interesting store. Lots of different things to look at.